Unofficial (Simplified) Libreboot Documentation
  • Home
  • Building from source/
  • External SPI flashing/
  • Freedom in Libreboot/
  • Maintainance manual/
  • Operating systems/
  • Payloads/
  • Releases/
  • Targets/
    • ARM Chromebooks/
    • Emulation/
    • Other/
    • X86/
      • AMD pitfalls
      • Boards/
        • Acer G43T-AM3
        • ASUS KCMA-D8 Desktop/Workstation
        • ASUS KFSN4-DRE Server/Workstation
        • ASUS KGPE-D16 Server/Workstation
        • Dell Latitude flashing
        • Dell Latitude thermal throttling
        • Dell OptiPlex 3050 Micro
        • Dell OptiPlex 7010/9010 MT
        • Dell OptiPlex 7010/9010 SFF
        • Dell OptiPlex 7020/9020 SFF/MT, and XE2 MT/SFF
        • Dell OptiPlex 780 MT/USFF
        • Dell Precision T1650
        • Gigabyte GA-G41M-ES2L Desktop
        • HP Compaq Elite 8300 USDT
        • HP Elite 8200 SFF/MT and 6200 Pro Business
        • HP EliteBook 2170p
        • HP EliteBook 2560p
        • HP EliteBook 2570p
        • HP EliteBook 820 G2
        • HP EliteBook 8460p
        • HP EliteBook 8470p
        • HP EliteBook 8560w
        • HP EliteBook Folio 9470m
        • Intel D510MO/D410PT
        • Intel D945GCLF Desktop
        • MacBook 1,1 and 2,1
        • ThinkPad R400
        • ThinkPad T400 external flashing
        • ThinkPad T420 external flashing
        • ThinkPad T440p external flashing
        • ThinkPad T480/T480s
        • ThinkPad T500 external flashing
        • ThinkPad T60 recovery guide
        • ThinkPad W541/W540 external flashing
        • ThinkPad X200 first-time flashing
        • ThinkPad X220/X220T
        • ThinkPad X230/X230T external flashing
        • ThinkPad X60 recovery
        • ThinkPad X60 Tablet recovery
        • ThinkPad X60/X60T/T60 internal flashing
      • Changing the MAC address
      • Disabling /dev/mem protections
      • Disabling Intel Boot Guard on MEv11
      • EC firmware updates
      • Generic internal flashing
      • Insert vendor files
      • Intel pitfalls
      • Ivybridge internal flashing
      • Microcode
      • nvmutil import
      • nvmutil manual
  • UNCATEGORIZED/
Site license: GFDL v1.3 with disclaimer

ThinkPad T60 recovery guide

Only the Intel GPU is compatible. Do not flash the ATI GPU models.

“Unbricking” means flashing a known-good (working) ROM. The problem: you can’t boot the system, making this difficult. In this situation, external hardware is needed which can flash the SPI chip (where libreboot resides). First, disassemble the machine using the following steps, and refer to the external flashing guide linked later from this guide.

Remove those screws and remove the HDD:

Lift off the palm rest:

Lift up the keyboard, pull it back a bit, flip it over like that and then disconnect it from the board:

Gently wedge both sides loose:

Remove that cable from the position:

Now remove that bezel. Remove wifi, nvram battery and speaker connector (also remove 56k modem, on the left of wifi):

Remove those screws:

Disconnect the power jack:

Remove nvram battery:

Disconnect cable (for 56k modem) and disconnect the other cable:

Disconnect speaker cable:

Disconnect the other end of the 56k modem cable:

Make sure you removed it:

Unscrew those:

Make sure you removed those:

Disconnect LCD cable from board:

Remove those screws then remove the LCD assembly:

Once again, make sure you removed those:

Remove the shielding containing the motherboard, then flip it over. Remove these screws, placing them on a steady surface in the same layout as they were in before you removed them. Also, you should mark each screw hole after removing the screw (a permanent marker pen will do), this is so that you have a point of reference when re-assembling the system:

This photo shows the flash chip, near the RAM, with numbers of pins written:

Refer to the external flashing guide:

Externally rewrite 25xx NOR flash via SPI protocol

NOTE: Do not use the 3.3v rail from your SPI programmer. Leave that disconnected. For 3.3v, plug your charger into the motherboard (but do not power on the mainboard) when the clip is connected. Before removing the clip, disconnect the charger. This will provide adequate 3.3v DC at correct current levels. The SPI flash on an X60 shares a common 3.3V rail with many other components on the motherboard, which all draw a lot of current, more than your flasher can provide.

Example command:

sudo ./flashprog -p linux_spi:dev=/dev/spidev0.0,spispeed=4096 -w libreboot.rom -V

If flashprog complains about multiple flash chips detected, just pass the -c option as it suggests, and pick any of the chips it lists. spispeed=4096 or lower (e.g. spispeed=512) is recommended on this board. The flashing becomes unstable, on this machine, when you use higher speeds.

Reverse the steps to re-assemble your system, after you’ve flashed the chip.

It should be Verifying flash... VERIFIED at the end. If flashprog complains about multiple flash chip definitions detected, then choose one of them following the instructions in the output.

Put those screws back:

Put it back into lower chassis:

Attach LCD and insert screws (also, attach the lcd cable to the board):

Insert those screws:

On the CPU (and there is another chip south-east to it, sorry forgot to take pic) clean off the old thermal paste (with the alcohol) and apply new (Artic Silver 5 is good, others are good too) you should also clean the heatsink the same way

Attach the heatsink and install the screws (also, make sure to install the AC jack as highlighted):

Reinstall that upper bezel:

Do that:

Re-attach modem, wifi, (wwan?), and all necessary cables. Sorry, forgot to take pics. Look at previous removal steps to see where they go back to.

Attach keyboard and install nvram battery:

Place keyboard and (sorry, forgot to take pics) reinstall the palmrest and insert screws on the underside:

It lives!

Always stress test (‘stress -c 2’ and xsensors. below 90C is ok) when replacing cpu paste/heatsink: